Occupational exposure to organotin substances: Development of a liquid chromatographic separation method for 11 organotin compounds in workplace air samples via HPLC-ICP-MS.

Organotin compounds (OTCs) are widely regulated but rank among the most used organometallic compounds in various industrial sectors. They are significantly more toxic than inorganic tin compounds. At workplaces, OTCs can be released as vapors or dust particles and can be absorbed by inhalation or skin contact. Occupational exposure thus represents a great risk for the absorption of OTCs for employees. Methods for OTCs speciation in workplace air monitoring currently do not exist. This study describes the development of a separation method for eleven in Germany regulated OTCs via HPLC-ICP-MS. The method allows a near baseline separation of MMT, MBT, MOT, MPhT, DMT, DBT, DPhT, TMT, TBT, TPhT and TTMT within 22 min on a C18 column and a ternary solvent and flow rate gradient using methanol, acetonitrile, and ultrapure water + 6% (v/v) acetic acid + 0.17% (m/v) α-tropolone. Ten analytes show linearity in the working range of 10 - 100 µg OTCs/L with R² > 0.999. Due to its high volatility the analyte TTMT showed a quadratic relationship between concentration and signal intensity with R² = 0.9998. The determination of the instrumental limits resulted in detection limits between 0.14 and 0.57 µg Sn/L and limits of quantification between 0.49 and 1.97 µg Sn/L. Over the course of this study thermal instability and cross reactivity of OTC in solution became apparent. Formation of two reaction products in mixed OTCs solutions have been observed. These effects will further be examined within development of appropriate sampling and sample preparation for workplace air to provide a suitable method for the determination of OTCs at workplaces according to normative references.

Comparison of Microwave-Assisted Digestion and Consensus Open-Vessel Digestion Procedures for Evaluation of Metalliferous Airborne Particulate Matter.

Metal occupational exposure limits mainly focus on total content of the respective metals of interest. The methods applied for trace metal analysis in occupational health and safety laboratories are usually standardized to pragmatic consensus digestion schemes, ensuring comparability of results. The objective of the present study entailed the evaluation of a recently developed HNO3-only microwave-assisted digestion procedure by comparison with the German consensus hot-block digestion and other national digestion schemes. An inter-laboratory comparison test with participation of nine national occupational health and safety laboratories from Europe and North America was organized. For adequate emulation of what workers are at risk of inhaling four different industrial metal processing workplace dusts (electronic recycling, high-speed steel grinding, cylinder head cleaning, and battery combustion ash) were homogenized and sieved to the particle size < 100 µm diameter at IFA. The participants were asked to process air sample-typical amounts according to the German hot-plate technique, the IFA microwave-assisted digestion scheme as well as their national or in-house conventional digestion method for airborne dust and analyze for Cd, Co, Cr, Co, Fe, Mg, Ni, Pb, and Zn. Recoveries (relative to consensus open-vessel digestion) obtained for the new IFA microwave-assisted digestion were between 88 and 114% and relative reproducibility standard deviations were <10% for most metals of interest. The in-house digestion procedures applied varied widely but (whether microwave, hot block, or open vessel) yielded comparable results for the predominantly elemental alloy type dusts supplied. Results become more diverse for the combustion dust, especially if a combination of microwave-assisted digestion procedures with high temperatures and hydrofluoric acid is applied. ISO 15202-2 is currently being revised; this digestion procedure will be included as a possible variant in annex 2.

Occupational Exposure to Inhalable Manganese at German Workplaces.

Due to mounting evidence of neurotoxic effects of manganese (Mn) already at low concentrations, occupational exposure limits (OELs) have been adopted. We analyzed 5771 personal measurements of inhalable manganese (Mn) together with information on sampling conditions and job tasks from the German exposure database Messdaten zur Exposition gegenüber Gefahrstoffen am Arbeitsplatz (MEGA) to assess exposure levels in welders and other occupations between 1989 and 2015. Geometric means (GMs) of exposure to Mn were estimated for various occupational settings adjusted for 2-h sampling duration and analytical method, centered at 2009. Measurements below the limit of quantification (LOQ) were multiply imputed. The median concentration was 74 µg m-3 (inter-quartile range 14-260 µg m-3) in welders and 8 µg m-3 (inter-quartile range 100 µg m-3 were observed in gas metal and flux-cored arc welders and in shielded metal arc welders using consumables of high Mn content (>5%). Tungsten inert gas welding, laser welding and working in other occupations such as foundry worker, electroplater, or grinder were associated with GMs <10 µg m-3. A shorter sampling duration was associated with higher Mn concentrations. High-emission welding techniques require protective measures to cope with adopted OELs. Results of this study are useful to assess cumulative Mn exposure in community-based studies on neurotoxic effects.